How to Tie Bucktail Jig for Walleye: A Step-by-Step Guide
Learn how to tie bucktail jig for walleye with the right hook, hair and thread steps, plus tips for a durable, better-swimming jig that gets bites.
Updated November 2026
Learning how to tie bucktail jig for walleye means you can build a jig that suits the water you fish, holds up to toothy fish, and swims with a lively profile. The process is simple: secure the hair to a hook, wrap it tightly, finish the head, and check the balance before you fish it. Most of the work is in the wrapping and the finish.
Walleye are not as harsh on gear as stripers or bluefish, but they still chew through thin hair and soft thread. A well-tied bucktail holds its shape through many fish and keeps its action when you work it slowly along the bottom.
Shopping for one? See our guide: 6 Best Bucktail Jigs for Walleye Options: Our Picks Compared.
Gather Your Materials and Set Up
Before you start, lay out everything you need so you are not hunting for thread halfway through a wrap. Many walleye anglers prefer a jig hook in the 1/8 to 3/8 ounce range for rivers and shallow reservoirs, and heavier for deeper or current-swept water.
- Jig hook matched to your target weight
- Bucktail hair (deer tail, with the natural tips intact)
- Nylon or bonded thread in a color close to your hair
- Bobbin or thread holder
- Scissors, a hair stacker, and a small amount of head cement or epoxy
Step-by-Step: Tying the Bucktail
Secure the Thread and Hair
Clamp the hook in a vise and start the thread a few millimeters behind the eye. Wrap back toward the bend to create a base that will grip the hair. Cut a small clump of bucktail, remove the short underfur, and align the tips in a hair stacker so they sit evenly.
Tie the Hair to the Shank
Place the hair on top of the hook shank so the tips extend past the bend. Make two or three tight wraps over the butts, then add a few more to lock them down. Keep the hair on top of the shank, not spread around it, so the jig rides upright in the water.
Build the Body and Finish the Head
Trim the butts flush at a slant so the wrap head is smooth. Wrap the thread forward to form a neat head, leaving enough room for the eye. Whip-finish, cut the thread, and apply a thin coat of head cement or epoxy. Let it cure fully before you fish it.
Checking Balance and Action
Hold the finished jig by the eye and let it hang. A balanced jig hangs with the hook point slightly up and the hair flowing straight back. If the hook rolls to one side, trim a little hair from the heavy side or adjust the wrap position on your next tie.
Common Mistakes
- Wrapping the hair too loosely, which lets it slide off the shank under pressure.
- Using too much hair, which slows the fall and fouls the hook point.
- Skipping the head finish, which lets water and teeth loosen the wraps.
- Tying the hair with the butts sticking out at an angle, which causes spinning.
- Fishing the jig before the cement cures, which can crack the head.
Recommended Gear
A hair stacker keeps the tips aligned so your jig swims evenly and looks clean. View on Amazon
A bobbin with tension control helps you keep consistent wraps and prevents thread breakage on the final turns. View on Amazon
Bonded tying thread holds up well when wrapped under tension and resists fraying during the finish. View on Amazon
For a deeper look at related setups, see Tying a Bucktail Jig: A Step-by-Step Guide for Saltwater Anglers and Bucktail Jig Tying Tips: How to Tie a Durable, Better-Swimming Jig. If you want to know how to work the finished jig, How to Work a Bucktail Jig: A Step-by-Step Guide for Saltwater Anglers covers retrieve styles that suit walleye.
FAQ
What hook size should I use for walleye bucktails?
Many anglers use a jig hook between 1/8 and 3/8 ounce for walleye, depending on depth and current. Heavier hooks help you hold bottom in faster water.
What kind of hair works best?
Deer tail is the usual choice because it is strong, buoyant enough to swim well, and holds its shape. Trim away the short underfur so the hair flows freely.
How long does head cement need to cure?
Follow the manufacturer’s directions on the bottle, which typically specify several hours for a usable finish and longer for full hardness. Let the jig cure completely before fishing to avoid cracked heads.
Conclusion
Tying a bucktail for walleye comes down to secure wraps, balanced hair, and a clean finished head. Practice the wrapping until it feels routine, and check each jig’s balance before it goes in the water. A durable jig that swims true will keep you fishing longer between tackle changes.
Related reading
Ready to choose one?
