How to Use a Conventional Reel for Trolling: A Step-by-Step Guide
Learn how to use a conventional reel for trolling, from spooling and setting the drag to handling strikes and retrieving your lure safely.
Updated November 2026
Learning how to use a conventional reel for trolling comes down to four things: spooling it correctly, setting the drag, controlling the line as the boat moves, and fighting fish without losing them. Once you have those basics, a conventional reel gives you far more control over depth, lure action and hook sets than a spinning reel can. This guide walks through each step in order.
Set Up the Reel Before You Leave the Dock
Start by matching your reel to your rod and line. Most trolling setups use a reel with a star drag, a smooth clicker and a line capacity suited to the species you are targeting. Check the rod’s line-weight rating and the reel’s spool capacity, then spool the line so the spool is filled to about 1/8 inch below the lip. Braid needs a backing line of monofilament or fluorocarbon underneath it to prevent slipping, and the braid should be wound on tight with steady tension.
Shopping for one? See our guide: 4 Best Penn Warfare Level Wind Conventional Reels of 2026.
Set the Drag and Rod Position
Drag determines how much pressure the line can take before it slips. A common starting point is about 25 to 33 percent of the line’s breaking strength, then adjust once you hook a fish. Pull line off the reel by hand; it should release smoothly without a jerky feel. Keep the rod in a rod holder with the tip angled slightly up, and check that the reel is in gear and the clicker is on if you want an audible alert on a strike.
Handle Strikes and Set the Hook
- Watch the rod tip and the clicker. A fish that grabs a lure usually makes the rod bend or the tip dip.
- Let the fish take line for two or three seconds so it swallows the bait, especially with live or cut bait.
- Engage the reel and sweep the rod back firmly, keeping the rod tip pointed toward the fish.
- Start cranking steadily while keeping the rod at roughly a 45-degree angle.
With artificial lures, a firm sweep is usually enough. Live bait often calls for a longer pause before the hookset.
Fight the Fish and Land It
Use the rod’s backbone to pump the fish: lift the rod, then drop it while reeling in the slack. Keep constant pressure on the fish, but never let the drag go so tight that the line can’t give. If the fish runs, let the drag do the work and point the rod at the fish to keep the line from rubbing against the hull or motor. When you have a fish near the boat, slow the boat or turn it so the fish comes up on the side you can reach. Use a gaff, net or leader grip to land it, and keep the leader in hand before lifting.
Common Mistakes
- Overfilling or underfilling the spool, which causes poor casting and line slippage.
- Setting the drag too tight, which can snap line or pull the hook.
- Forgetting to engage the reel before a hookset, leaving the line slack.
- Ignoring the leader. Check it after every few fish for nicks or abrasion.
- Letting line tangle on the spool during reel-in. Keep steady tension when winding.
Recommended Gear
- Penn Fathom II conventional reel: a star drag model many saltwater anglers use for trolling because the drag is adjustable in fine steps. View on Amazon
- Seaguar Gold Label fluorocarbon leader: a common leader material for trolling because it resists abrasion from teeth and structure. View on Amazon
FAQ
How much line should go on a conventional reel for trolling?
Fill the spool to about 1/8 inch below the lip. Overfilling reduces casting distance and can cause line to bind during a run.
What drag setting should I use when trolling?
Many anglers start around 25 to 33 percent of the line’s breaking strength and adjust after the first strike. Test the drag by pulling line by hand before you set the hook.
Do I need to keep the clicker on?
Leaving the clicker on gives you an audible alert when a fish takes line, which helps when you are watching multiple rods.
Conclusion
Using a conventional reel for trolling is mostly about preparation: spool correctly, set the drag and keep the rod positioned well. Practice the strike and fight sequence until it feels automatic. Consistent habits on the water will save you more fish than any single piece of gear.
Related reading
- How to Use Conventional Reel Without Level Wind: A Step-by-Step Guide
- How to Cast a Conventional Reel Without Backlash: 6 Steps That Work
- How to Cast Conventional Reel: A Step-by-Step Guide for Beginners
- The Lightest Conventional Reel: What Makes One Light and Which Ones to Consider
- Penn Fathom II Star Drag Conventional Reel: 5 Best Picks Compared (2026)
Ready to choose one?
